INGREDIENT CHEMICAL NAME

OSHA PEL

ACGIH TLV

OTHER LIMITS RECOMMENDED

CAS NUMBER

Benzotriazole UV Absorber

N/A

N/A

N/A

25973-55-1

Butyl Benzyl Phthalate

N/A

N/A

N/A

85-68-7

Pigments

N/A

N/A

N/A

Not established

N-Butyl Acetate

150 ppm

150 ppm

N/A

123-86-4

Toluene

200 ppm

100 ppm

N/A

108-88-3

Propylene Glycol Monomethyl Ether Acetate

N/A

N/A

N/A

108-65-6

Xylene

100 ppm

100 ppm

N/A

1330-20-7

Methyl Ethyl Ketone

200 ppm

200 ppm

N/A

78-93-3

Isopropyl Alcohol, Anhydrous

400 ppm

400 ppm

N/A

67-63-0

Acetone

1,000 ppm

750 ppm

N/A

67-64-1

Light Aliphatic Solvent Naphtha

N/A

N/A

N/A

64742-89-8

Medium Aliphatic Solvent Naphtha

N/A

N/A

N/A

64742-88-7

Light Aromatic Solvent Naphtha

N/A

N/A

N/A

64742-95-6

Film Formers, Resins, and Additives

N/A

N/A

N/A

Not established

BOILING POINT:

66-205 ° C

SPECIFIC GRAVITY (H2O=1):

1.0-1.3

VAPOR PRESSURE (mm Hg):

8-19 mmHg

MELTING POINT:

N/A

VAPOR DENSITY (AIR = 1):

Heavier than air

EVAPORATION RATE (Butyl Acetate = 1):

100

SOLUBILITY IN WATER:

0-2%

APPEARANCE AND ODOR:

Viscous liquid with an odor characteristic of the solvents listed in section II.

FLASH POINT (METHOD USED):

72 ° F PMCC

FLAMMABLE LIMITS

LEL: 1.3 UEL: U/1

EXTINGUISHING MEDIA:

WATER FOG

STANDARD FOAM x

CO 2 x

DRY CHEMICAL x

HALON

UNUSUAL FIRE AND EXPLOSION HAZARDS:

Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, and open flames. Closed containers may explode when exposed to extreme heat. Do not apply on hot surfaces. Toxic gases may form when product is contacted by flame or hot surfaces.

SPECIAL PRECAUTIONARY STATEMENTS:

Water spray may be ineffective. Water spray may be used to cool. Closed containers to prevent pressure build-up and possible autoignition or explosion when exposed to extreme heat. If water is used, fog nozzles are preferable. Fire-fighters should wear self contained breathing apparatus.

STABILITY:

x Stable Unstable

Incompatibility :

Avoid contact with strong alkalies, strong mineral acids, or strong oxidizing agents.

Hazardous Decomposition:

May produce hazardous decomposition products when heated. Welding, brazing, or flame-cutting on surfaces coated with this product may produce fumes including: Carbon Monoxide

HAZARDOUS POLYMERIZATION:

May Occur x Will not occur

Conditions to Avoid:

INGESTION:

Harmful or fatal if swallowed.

EYES:

Causes severe eye irritation.

INHALATION:

Vapor and spray mist may be harmful if inhaled. Vapor irritates eyes, nose, and throat. Repeated exposure to high vapor concentrations may cause irritation of the respiratory system and permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

SKIN:

May cause moderate skin irritation. May be absorbed through the skin.

INGESTION:

If swallowed, do not induce vomiting.

EYES:

In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes.

INHALATION:

If affected by inhalation of vapor or spray mist. Remove to fresh air. Apply artificial respiration and other supportive measures as required.

SKIN:

In case of skin contact, remove promptly by wiping, followed by waterless hand cleaner and soap and water.

STEPS TO BE TAKEN IN CASE LARGE AMOUNTS ARE RELEASED:

Provide maximum ventilation. Only personal equipment with proper respiratory and skin and eye protection should be permitted in the area. Remove all sources of ignition. Take up spilled material with sawdust, vermiculate, or other absorbent material and place into containers for disposal.

WASTE DISPOSAL METHOD:

Waste material must be disposed of in accordance with federal, state, provincial, and local environmental control regulations. Empty containers should be recycled or disposed of through an approved waste management facility.

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:

Do not store above 120 ° F. Store large quantities in buildings designed and protected for storage of NFPA Class IB flammable liquids.

OTHER PRECAUTIONS:

If this material is part of a multiple component coating system. Read the material safety data sheet(s) for the other component or components before blending as the resulting mixture may have the hazards of all of its parts. Containers should be grounded when pouring. Avoid free fall of liquids in excess of a few inches.

RESPIRATORY PROTECTION:

Overexposure to vapors may be prevented by ensuring ventilation controls. Vapor exhaust or fresh air entry. NIOSH/MSHA-approved (TC-23C-) paint spray or air supplied (TC-19C-) respirators may also reduce exposure. Read respirator manufacturer's instructions and literature carefully to determine the type of airborne contaminants against which the respirator is effective and how it is to be properly fitted.

VENTILATION:

Provide general dilution or local exhaust ventilation in volume and pattern to keep the concentration of ingredients listed in section II below the lowest suggested exposure limits. The LEL in section IV below the stated limit and to remove decomposition products during welding or flame cutting on surfaces coated with this product.

LOCAL EXHAUST:

N/A

PROTECTIVE GLOVES:

Gloves constructed of: Nitrile Rubber, neoprene rubber or polyvinyl alcohol.

EYE PROTECTION:

Wear chemical-type splash goggles or full face shield.

HEALTH : 3

HAZARD RATING KEY

FLAMMABILITY : 3

0 = MINIMAL

REACTIVITY : 0

1 = SLIGHT

PERSONAL PROTECTION :

2 = MODERATE

3 = SERIOUS

4 = SEVERE

* = CHRONIC HEALTH EFFECTS